Owner's ManualI CRAFI",'SMAN+I42"- 2 STAGE SNOW THROWERTRACTO R ATTAC HMENTModel No. 486.248392CAUTION:Before using this product,
eAssemble the short "V" belt onto the engine pulleyand then onto the large pulley on top of the clutch/idler assembly. The belt must be plac
• Remove the engine pulley keeper from the side ofthe tractor frame by removing the washer and nutthat secure the keeper. Attach the new pulleykeeper
ELECTRIC ATTACHMENT CLUTCHES• Turn the clutch/idler assembly upside down andplace the extra tensioning chain through the leftfront hole as shown in fi
Hold this drawing above you while viewing theClutch/idler Assembly from underneath thetractor. Right and left in the drawing will be thereverse of the
• Tilt the snow thrower back down to the ground.• Remove the nylon tie which fastens the auger drivebelt to the discharge housing, leaving the beltass
ATTACHING SNOW THROWER TO TRACTORNOTE: An additional person's help may be required tomount the snow thrower to the front of the tractor.• Place t
INSTALLINGTHEATTACHMENTPINLiftthefront of the snow blower to align the holesin the mounting plates and the side plates. Fromthe left side of the tract
• Place the plastic keg on the weight tray and fill withapproximately 75 Ibs. of dry sand.• Secure the keg with the rubber tarp strap hookedinto the h
KNOW YOUR SNOW THROWERRead this owner's manual and safety rules before operating your snow thrower.Compare the illustrationbelow with your snow t
RAISING AND LOWERING• To raise, push down on the lift handle until thesnow thrower locks in the raised transport position.• To lower, push down slight
ACCESSORIES ... 2SAFETY RULES ... 3FULL
&CAUTION: Before servicing or adjustingthe snow thrower, shut off the engine,remove the spark plug wire(s), set theparking brake and remove the ke
STORAGE RECOMMENDATIONS• Lower the snow thrower to the ground.• Remove the snow thrower from the tractor.• Clean the snow thrower thoroughly. Wash off
2127REPAIR PARTS FOR MODEL 486.248392 42" SNOW THROWER9163333 38 1578 28 2977937O105112221221/30 24391 98 9221 _==_634454 6127214765 82 4,8265276
REPAIR PARTS FOR MODEL 486.248392 42" SNOW THROWERREF.NO.1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484
REPAIR PARTS FOR MODEL 486.248392 42" SNOW THROWER47 51_f / 5063 74145256//696O6O\7357\18 65\7912/82162831/5\\7361 603880761822\36757829232435356
REFNO.123456891012131415161718192O2122232425262728293031323334353637383940REPAIR PARTS FOR MODEL 486.248392 42" SNOW THROWERPART QTY DESCRIPTION
NOTES26
r_|||!I|I|!CAUTION: DO NOT OPERATE YOUR TRACTOR AND SNOWTHROWER ON A SLOPE IN EXCESS OF 10 DEGREES. BE SURE OFYOUR TRACTOR'S TOWING AND BRAKING C
For repair of major brand appliances in your own home...no matter who made it, no matter who sold it!1-800-4-MY-H O MEsMAnytime, dayor night(1-800-469
Anypowerequipmentcancauseinjuryif operatedimproperlyor if the userdoesnotunderstandhowto operatethe equipment.Exercisecautionat all times,whenusingpow
SHOWN ACTUAL SIZENOT SHOWN ACTUAL SIZEfDD/MMREF.ABCDEFGHIJKLMNOPQRSQTY.142624226241101427212DESCRIPTION REF. QTY. DESCRIPTIONHex Bolt, 1/2" x 1-1
CARTON CONTENTS1. Cross Brace (Weight Tray)2. Side Brace (Weight Tray)3. Right Hand Side Plate (Stamped "R")4. Left Hand Side Plate (Stamped
TOOLS REQUIRED FOR ASSEMBLYINSTALLING SIDE PLATES ON TRACTOR(2) 7/16" Wrenches(2) 1/2" Wrenches(2) 9/16" Wrenches(2) 3/4" Wrenches
• Assemble a shoulder bolt, a 3/8" lock washer and a3/8" hex lock nut to the bottom hole in each sideplate. See figure 3.• Proceed to page 8
INSTALLING HANGER BRACKETSFor better clearance, lower the tractor's suspensionarms using the attachment lift lever.On Tractors With Foot Rest Bra
INSTALLING CLUTCH/IDLER ASSEMBLYThissectioncoverstheinstallationof theClutch/Idlerassembly to tractors with attachment clutches that areeither rod ope
Kommentare zu diesen Handbüchern