Sears 113.22643 Bedienungshandbuch

Save This Manual ForFuture ReferenceBELT AND DiSCSANDERSerialNumberModel and serial number may befound on the back side of the baseYou should record b

assemblyAUXILIARY MOUNTING FOR VERTICALSANDING1. Remove backstoplock bolt and removework support.2. Removetable assembly by removingtable lock knoband

3. Slide tension lever to the left to apply belt tension.4. Tighten hex socket screw when bed is in desiredposition.5. Plug in the power cord. Turn sw

4TENSIONLEVER6AUXILIARYMOUNTING HOLE WORK SUPPORT/ HEX SCREWBED3TRACKINGKNOB2BED LOCKINGHEX SOCKETHEAD SCREW5TABLE LOCKKNOBHOLE1WORK SUPPORTSANDINGBEL

ON-OFF SWITCHThe On-Off switch has a locking feature. THIS FEA-TURE IS INTENDED TO HELP PREVENT UNAUTHOR-IZED AND POSSIBLY HAZARDOUS USE BY CHIL-DREN

BEFORE USING THE SANDERWARNING: To avoid mistakes that could causeserious, permanent injury, do not plug the sander inuntU the following steps are com

Dressfor safety,Any power sander can throw foreign objects into theeyes. This can cause permanent eye damage. Wearsafety goggles (not glasses) that co

ibas c operationBEVEL SANDINGThe worktable can be tilted from 0oto 45° for bevelsanding. Loosen the table lock knob and tiltthe work-table to desired

SURFACE SANDING ON THE SANDINGBELTWARNING: To avoid injury from sflps, jams orthrown pieces, adjust the backstop to clear thesanding surface by no mor

basic operationAlways sand outside curves onthe left side ofcenter onthe sanding disc as shown.WARNING: Applying the workplece to the right sideof the

maintenanceWARNING: For your own safety, turn switch "OFF"and remove plug from power source outlet beforeadjuSting, maintaining, or lubrlcst

FULLONE YEAR WARRANTY ON CRAFTSMAN BELT AND DISC SANDERIfwith In one year from the data of purchase, th Is Craftsman BeIt and Disc Sander fails due to

maintenance4. Slightlytighten (3) screws. Adjust tension of belt byputting blade screwdriver in adjusting hole. Push upon screwdriver to tighten tensi

troubleshootingWARNING: For your own safety, turn switch "OFF"and remove plug from power source outlet beforetroubleshooting your sander.TRO

repair partso\!/22

repair partsPARTS LiST FOR CRAFTSMAN BELT AND DiSC SANDERMODEL 113.226430KeyNo.12345PartNo.8202478201758211568194968202356 8202497 STD8520066 8202389

SERVICEMODEL NO.113.226430HOW TO ORDERREPAIR PARTSBELTAND DISCSANDERNow that you have purchased your Belt and DiscSander, should a need ever exist for

BEFORE EACH USE:Inspect your sander.DISCONNECT THE SANDER. To avoid injury fromaccidental starting, unplug the sander, turn the switch offand remove t

safety instructions for belt and disc sander• Wear nonslip footwear. Plan the way you will hold the workpiece from startto finish.• Noise levels vary

motor specifications and electricalrequirementsThis machine is designed to use, and is equipped with,a3450 RPM motor. It is wired foroperation on 120

contentsPOWER TOOL WARRANTY ... 2SAFETY INSTRUCTIONS FORBELT D)SC SANDEF ... 2MOTOR SP

assembJyMOUNTING BELT AND DISC SANDERTO WORKBENCHIf belt and disc sander is to be used in a permanentlocation, itshould be fastened securely to afirm

assemblyINSTALLING SANDING DiSC AND GUARD1. Locate sanding disc and pee backing from disc.Align perimeter ofdiscwith I_late and press disc firmlyinto

4. Locatewasher 6.5 x 17.8 x 1.6 and knob among loosepads,5. Position table support in corresponding holes on sideof base as shown. Make sure the 9.5r